|
rigparts272
Power Supply Three phase 690V – 50Hz/60Hz, 48V Frequency converter can achieve 20Hz to the rated frequency of regulation The number of poles There are 6 commonly used, the other is very custom In accordance with the following provisions of Europe Low voltage 89/336/CE; electromagnetic compatibility 73/23/CE Refer to the following standards EN600034-1, EN50081-1, EN50081-2, EN50082-1, EN50082-2 performance In the maximum eccentric force and the maximum power supply, can be continuous operation, but also can be interrupted. It depends on the type of vibrator and operating environment. For more information, please contact our technical department. centrifugal force Max up to 50000Kgf (490KN). Output centrifugal force adjustment range 0 to 100% Mechanical protection According to EN60529, IEC529 regulations: IP66 Earthquake protection According to EN50102, IEC68 regulations: IK08 Insulation grade F Class (155 C); H Class (180 C) to be customized Heat resistance Manufacturing process using drip plastic forming ambient temperature From -30 to +40 degrees Celsius, the use of other environmental temperature with the manufacturers to confirm A thermal protector The standard vibrator is 130 DEG C (DIN44081-44082) thermistor thermistor for temperature protection or other anti frosting heater, please contact with the factory. install In any position can be installed, two vibrators connected by joint coupling lubrication All have been filling in vibrator factory lubricating oil, under normal conditions without the addition of lubricating oil, but under heavy conditions, frame size 35 and above models need to add the lubricating oil and the vibrator Junction box For fixing an electrical connection wire, a terminal with a special shape can be provided for fixing the power cord to avoid joint loosening. Electric machinery The three-phase asynchronous motor, designed to meet the vibration of the machine when starting the required maximum starting torque and torque curve design, frame size to AF33, 35 of the vibrator are vacuum injection molding process, vibrator frame more by plastic molding manufacturing. Shell Vibrator shell frame size 35 below the high strength Aluminum Alloy, frame size greater than using ductile iron 35, special shape design patent is beneficial to heat radiation, under normal conditions, full load operation when the temperature is much lower. Bearing base Ductile iron or gray cast iron. Bearing flange flange Bearing Ductile cast iron. The geometric structure of the flange can transmit the load to the outer shell. Bearing Bearings Special customization, tailored specifically for Italvibras, is applicable for both axial and radial loads. Motor shaft shaft Motor Aluminum alloy constant temperature quenching treatment, can reduce the stress. One end shaft extends out to connect the coupling. Eccentric block weights Eccentric The centrifugal force can be continuously adjusted, and the centrifugal force is indicated by the percentage of the centrifugal force. A patent system called ARS (patent number: M098A000194) can prevent the adjustment error. Eccentric block end cap covers Weight The Aluminum Alloy material from the shaft end of the eccentric block cover is divided into two pieces, so that can open the cover even two eccentric vibrator are connected together Paint Painting Spray salt test with epoxy resin powder for 500 hours at 200 C.
Power Supply Three phase 690V – 50Hz/60Hz, 48V Frequency converter can achieve 20Hz to the rated frequency of regulation The number of poles There are 6 commonly used, the other is very custom In accordance with the following provisions of Europe Low voltage 89/336/CE; electromagnetic compatibility 73/23/CE Refer to the following standards EN600034-1, EN50081-1, EN50081-2, EN50082-1, EN50082-2 performance In the maximum eccentric force and the maximum power supply, can be continuous operation, but also can be interrupted. It depends on the type of vibrator and operating environment. For more information, please contact our technical department. centrifugal force Max up to 50000Kgf (490KN). Output centrifugal force adjustment range 0 to 100% Mechanical protection According to EN60529, IEC529 regulations: IP66 Earthquake protection According to EN50102, IEC68 regulations: IK08 Insulation grade F Class (155 C); H Class (180 C) to be customized Heat resistance Manufacturing process using drip plastic forming ambient temperature From -30 to +40 degrees Celsius, the use of other environmental temperature with the manufacturers to confirm A thermal protector The standard vibrator is 130 DEG C (DIN44081-44082) thermistor thermistor for temperature protection or other anti frosting heater, please contact with the factory. install In any position can be installed, two vibrators connected by joint coupling lubrication All have been filling in vibrator factory lubricating oil, under normal conditions without the addition of lubricating oil, but under heavy conditions, frame size 35 and above models need to add the lubricating oil and the vibrator Junction box For fixing an electrical connection wire, a terminal with a special shape can be provided for fixing the power cord to avoid joint loosening. Electric machinery The three-phase asynchronous motor, designed to meet the vibration of the machine when starting the required maximum starting torque and torque curve design, frame size to AF33, 35 of the vibrator are vacuum injection molding process, vibrator frame more by plastic molding manufacturing. Shell Vibrator shell frame size 35 below the high strength Aluminum Alloy, frame size greater than using ductile iron 35, special shape design patent is beneficial to heat radiation, under normal conditions, full load operation when the temperature is much lower. Bearing base Ductile iron or gray cast iron. Bearing flange flange Bearing Ductile cast iron. The geometric structure of the flange can transmit the load to the outer shell. Bearing Bearings Special customization, tailored specifically for Italvibras, is applicable for both axial and radial loads. Motor shaft shaft Motor Aluminum alloy constant temperature quenching treatment, can reduce the stress. One end shaft extends out to connect the coupling. Eccentric block weights Eccentric The centrifugal force can be continuously adjusted, and the centrifugal force is indicated by the percentage of the centrifugal force. A patent system called ARS (patent number: M098A000194) can prevent the adjustment error. Eccentric block end cap covers Weight The Aluminum Alloy material from the shaft end of the eccentric block cover is divided into two pieces, so that can open the cover even two eccentric vibrator are connected together Paint Painting Spray salt test with epoxy resin powder for 500 hours at 200 C.
Power Supply Three phase 690V – 50Hz/60Hz, 24V Single phase 100V-130V, 60Hz 200V-240V, 50Hz Frequency converter can achieve 20Hz to the rated frequency of regulation The number of poles 2 pole or 4 pole In accordance with the following provisions of Europe Low voltage ATEX; 94/9/EC 2006/95/EC Refer to the following standards 61241-0 IEC/EN, 61241-1 EN, 60034-1. IEC/EN performance In the maximum eccentric force and the maximum power supply, can be continuous operation, but also can be interrupted. It depends on the type of vibrator and operating environment. For more information, please contact our technical department. centrifugal force Max up to 311Kgf (3.05KN), centrifugal force can be adjusted by the adjustable eccentric block Mechanical protection According to EN60529, IEC529 regulations: IP66 Earthquake protection According to EN50102, IEC68 regulations: IK08 Insulation grade F Class (155 C) Heat resistance Vacuum injection molding process ambient temperature From -20 to +40 C, the other temperature needs to be customized. A thermal protector Please customize with a thermal detector 130 C thermal protector (DIN4408144082) install In any position can be installed in the junction box, and the vibrator bottom, mounting holes on the same side. lubrication Fully sealed ball bearings, using lifetime lubrication. Junction box Used for fixing the electric connecting wire and strengthening the structure of the junction box, which can prevent the internal explosion. Can provide a special shape of the terminal, used to fix the power cord to avoid joint loosening. Electric machinery Three phase induction motor, stator coil using vacuum injection molding, the rotor is aluminum die casting Shell Aluminum alloy with good ductility and good ductility. Bearing flange Nodular cast iron, the structure can make the load evenly transmitted to the shell. Motor shaft shaft Motor Aluminum alloy constant temperature quenching treatment, can reduce the stress Eccentric block weights Eccentric Can be convenient to adjust the vibration power from 0 to 100% Eccentric block end cap covers Weight The Aluminum Alloy casting high strength and surface by sandblasting treatment
VBB-326-W VBB-546-W VBB-1076-W VBB-20156-W VBB-32246-W VBB-4 VBB-314-W VBB-534-W VBB-1054-W VBB-1684-W VBB-20114-W VBB VB-50308-W VB-75558-W VB-100758-W VB-135908-WA VB-1601108-W VB-112-W VB-322-W VB-552-W VB-1082-WA VB-10102-W VB-20182-W VB-314-W VB-534-W vibratory motor VB-634-W VB-1054-WA VB-1264-W VB-1584-W VB-20114-W VB-32154-W VB-50234-W VB-75374-W VB-80554-W VB-84554-W VB-100634-W VB-145894-W VBB series flameproof vibration motor is the use of the company’s successful technology VB Series vibration motor, flameproof and foreign advanced technology, the technology explosion and vibration technology, designed specifically for oilfield solids control equipment and design products, protective shell rating of IP55, insulation class F, Ex logo ExdⅡBT4, places for class ⅱ T4 group flammable gas or vapor and air to form an explosive mixture in the oil field <a Lastrigtechparts273Nextrigtechparts271 |
