SICHUAN HONG HUA MUD PUMP
HH MUD PUMP |
|
|
| NB800M.00
HHF-800 Drilling pump
Parts list |
|
| — | NB800M.00 HHF-800 General drawing of drilling pump” | 2 |
| 二 | Parts drawings of drilling pump | 6 |
| 1 | NB800M.01.00 Frame assembly | 6 |
| 2 | NB800M.02.00 Crankshaft assembly | 8 |
| 3 | NB800M.03.00 Pinion shaft assembly | 10 |
| 4 | NB800M.04.00 Crosshead assembly | 12 |
| 5 | NB800M.05.00 Fluid end assembly | 14 |
| 6 | NB800M.06.00 Power end lubrication assembly | 17 |
| 7 | NB800M.08.00 Spray pump assembly | 20 |
| 8 | NB800M.10.00 Breather cap | 22 |
| 9 | NB800M.15.00 Oil level gauge | 23 |
| 10 | NB800M.19.00 Clean out cover | 24 |
| 11 | NB800M.22.00 Draining filter assembly | 25 |
| 12 | NB800M.24.00 Elbow assembly | 26 |
| 13 | NB800M.24.00A Discharge five-way pipe | 27 |
| 14 | NB800M.27.00 KB-45Pulsation damper | 29 |
| 15 | NB800M.28.00 JA-3Shear pin Relieve valve | 31 |
| 一、NB800M.00 HHF-800 General drawing of drilling pump |
|
| S.N | Drawing No. | Item |
| 1 | NB800M.01.00 | Frame assembly |
| 2 | NB800M.02.00 | Crankshaft assembly |
| 3 | NB800M.03.00 | Pinion shaft assembly |
| 4 | NB800M.04.00 | Crosshead assembly |
| 5 | NB800M.05.00 | Fluid end assembly |
| 6 | ANSI/ASMEB 18.6.3-2003 | Screw: 8 (0.164) -32×1/2 |
| 7 | NB800M.06.00 | Power end lubrication assembly |
| 8 | NB800M.07.00 | Skid |
| 9 | NB800M.08.00 | spray pump assembly |
| 10 | NB800M.09 | Seal gasket |
| 11 | NB800M. 10.00 | Breather cap |
| 12 | NB800M.11 | Nameplate |
| 13 | NB800M.12.00 | Cover plate assembly |
| 14 | ANSI/ASMEB 18.2.1-1996 | Bolt: 1/2-13×1 1/4 |
| 15 | GB/T95-2002 | Washer: 14 |
| 16 | NB800M.13 | Seal pad |
| 17 | NB800M.14 | Indication plate |
| 18 | NB800M.15.00 | Oil level gauge |
| 19 | NB800M.16 | Adjusting gasket |
| 20 | ANSI/ASMEB 18.2.1-1996 | Bolt: 1-8×3 1/8 |
| 21 | GB/T93-1987 | Washer: 27 |
| 22 | ANSI/ASMEB 18.2.2-1987 (R1999) | Nut: 1-8 |
| 23 | NB800M.17 | Cover, crosshead hole |
| 24 | NB800M.18 | Seal pad |
| 25 | ANSI/ASMEB 18.2.1-1996 | Bolt: 1/2-13×1 3/8 |
| 26 | NB800M.19.00 | Clean out cover |
| 27 | NB800M.20 | Seal gasket |
| 28 | ANSI/ASMEB 18.2.1-1996 | Bolt: 5/8-11×2 |
| 29 | GB/T95-2002 | Washer: 16 |
| 30 | ANSI/ASMEB 18.2.2-1987 (R1999) | Nut: 5/8-11 |
| 31 | NB800M.21 | Screw plug: Rz1 1/2 |
| 32 | NB800M.22.00 | Draining filter assembly |
| 33 | NB800M.23 | Ring gasket: R44 |
| 34 | NB800M.24.00 | Elbow assembly |
| 35 | NB800M.24.00A | Discharge five-way pipe assembly |
| 36 | NB800M.25.00 | Special tools |
| 37 | NB800M.26 | Flange: 5 1/8*35 |
| 38 | NB800M.27.00 | KB-45 Pulsation dampener |
| 39 | NB800M.28.00 | JA-3 Shear pin relieve valve |
| 40 | NB800M.29.00 | Spare parts delivered with pump |
| 41 | NB800M.30.00 | Cover plates assembly |
| 42 | GB/T827-1986 | Rivet: 3*10 |
| 43 | YK-150 | Dual scale shock-proof pressure gauge: |
|
| 0~40MPa (0~5800psi) |
| 44 |
| Rubber: 30*10*4880 |
| 45 | NB800M.31 | Blind flange: 5 1/8*35 |
| 二、Parts drawings of drilling pump |
|
| S.N | Drawing No. | Item |
| 1 | NB800M.01.01.00 | Frame |
| 2 | NB800M.01.02 | Main bearing cover |
| 3 | NB800M.01.03 | Shim set |
| 4 | NB800M.01.04 | Connector: NPT3/4-NPT3/4 |
| 5 | NB800M.01.05 | Screw plug: NPT3/4 |
| 2、NB800M.02.00 Crankshaft assembly |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.02.01.00 | Cover, main bearing |
| 2 | NB800M.02.01A.00 | Cover, main bearing |
| 3 | NB800M.02.02 | Sleeve, main bearing (right) |
| 4 | NB800M.02.03 | Seal gasket |
| 5 | NB800M.02.04 | Insider retainer |
| 6 | NB800M.02.05.00 | Outside retainer |
| 7 | NB800M.02.06 | rod |
| 8 | NB800M.02.07 | Locating ring (I) |
| 9 | NB800M.02.08.00 | Crankshaft |
| 10 | NB800M.02.09 | Locating ring (II) |
| 11 | NB800M.02.10.00 | Bull gear |
| 12 | NB800M.02.10A | Bull gear (hobbing ) |
| 13 | NB800M.02.10B | Bull gear (gear grinding) |
| 14 | NB800M.02.11 | bolt: 1 1/8-8UN-2Ax125 |
| 15 | NB800M.02.11A | bolt: 1 1/8-8UN-2Ax100 |
| 16 | NB800M.02.12.00 | Locking nut: 1 1/8-8UN-2B |
| 17 | NB800M.02.13 | spacer ring |
| 18 | NB800M.02.14 | Bolt, main bearing: 2 1/4-8UN-3A |
| 19 | NB800M.02.15.00 | Shim set |
| 20 | NB800M.02.16 | Sleeve, main bearing (left) |
| 21 | NB800M.02.17 | retainer ring |
| 22 | NB800M.02.18 | Baffle plate |
| 23 | NB800M.02.19 | Bolt: 5/8-11×1 1/2 |
| 24 | ANSI/ASMEB 18.2.1-1996 | Bolt: 5/8-11×1 3/4 |
| 25 | GB/T97.2-1985 | Washer: 16 |
| 26 | GB/T343-1994 | Locking wire: SZ-1.50 |
| 27 | NB800M.02.20 | Bolt: 5/8-11×4 3/4 |
| 28 | NB800M.02.21 | Bolt: 5/8-11×4 |
| 29 | GB/T343-1994 | Locking wire: SZ-3.00 |
| 30 | NB800M.02.22 | Eccentric bearing: NUP 464775 Q4/C9YA4 |
| 31 | NB800M.02.23 | Main bearing: 23148/C3W33 |
| 32 | 242 | anaerobic adhesive for thread locking and sealing |
| 3、NB800M.03.00 Pinion shaft assembly |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.03.01 | Key: 1 3/4×1 3/4×8 |
| 2 | NB800M.03.02 | Pinion shaft |
| 3 | NB800M.03.02A | Pinion shaft (hobbing) |
| 4 | NB800M.03.02B | Pinion shaft (grinding) |
| 5 | NB800M.03.03 | Scuff Sleeve |
| 6 | NB800M.03.04 | End cover |
| 7 | NB800M.03.05 | Seal gasket |
| 8 | NB800M.03.06.00 | Oil collection box |
| 9 | NB800M.03.07 | Seal gasket |
| 10 | NB800M.03.08 | Baffle plate |
| 11 | NB800M.03.09 | Bearing sleeve |
| 12 | NB800M.03.10 | Seal gasket |
| 13 | GB/T93-1987 | washer: 16 |
| 14 | ANSI/ASME B18.2.1-1996 | bolt: 5/8-11×1 3/4 |
| 15 | NB800M.03.11 | paring disc pump flange |
| 16 | ANSI/ASME B18.2.1-1996 | bolt: 1/2-13×1 3/8 |
| 17 | GB/T93-1987 | washer: 14 |
| 18 | ANSI/ASME B18.2.1-1996 | bolt: 3/4-10×2 |
| 19 | GB/T93-1987 | washer: 20 |
| 20 | NB800M.03.12 | oil seal: 7.625″x9.125″x0.625″ |
| 21 | NB800M.03.13 | cylindrical roller bearing : NU3036X2M/C4 |
| 4、NB800M.04.00 Crosshead assembly |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.04.01 | crosshead |
| 2 | NB800M.04.02 | Slide, upper |
| 3 | GB/T4240-1993 | Stainless steel wire: (p1.60(L=300) |
| 4 | NB800M.04.03 | bolt: 3/4-10UNC-2Ax 1 1/2 |
| 5 | NB800M.04.04 | Double lip oil seal: 4″x5″x0.5″ |
| 6 | NB800M.04.05 | oil seal ring |
| 7 | NB800M.04.06 | stuffing box |
| 8 | GB/T3452.1-2005 | O ring: 160×3.55-G-S |
| 9 | NB800M.04.07 | Seal gasket |
| 10 | NB800M.04.08 | End cover |
| 11 | NB800M.04.09 | rod |
| 12 | NB800M.04.10 | Mud guard plate |
| 13 | NB800M.04.11 | Lock spring |
| 14 | ANSI/ASME B18.2.1-1996 | bolt: 3/8-16×1 3/8 |
| 15 | GB/T93-1987 | washer: 10 |
| 16 | GB/T3452.1-2005 | O ring: 128×7-G-S |
| 17 | GB/T3452.1-2005 | O ring: 103×5.3-G-S |
| 18 | NB800M.04.12 | Lockup plate |
| 19 | NB800M.04.13 | Slide, lower |
| 20 | GB/T4240-1993 | Stainless steel wire: (Φ1.60(L=500) |
| 21 | NB800M.04.14 | bolt: 3/4-10UNC-2Ax2 |
| 22 | NB800M.04.15 | Crosshead pin baffler |
| 23 | NB800M.04.16 | gasket |
| 24 | NB800M.04.17 | Bearing, crosshead: |
|
| NNAL 6/177.8-1 Q4/W33XYA2 |
| 25 | NB800M.04.18 | Crosshead pin |
| 26 | NB800M.04.19.00 | shim set |
| 27 | NB800M.04.20 | pipe connector: NPT3/8×50.8 |
| 28 | NB800M.04.21 | adjusting shim |
| 29 | GB/T4240-1993 | Stainless steel wire: (p1.60(L=400) |
| 30 | ASMEB 18.3-2002 | bolt: 5/8-11×2 |
| 31 | 242 | anaerobic adhesive for thread locking and sealing |
| 5、NB800M.05.00 Fluid end assembly |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.05.01.00 | Cylinder assembly |
| 2 | NB800M.05.02 | Cylinder cover flange |
| 3 | NB800M.05.03 | Cylinder cover |
| 4 | NB800M.05.04 | seal ring, linear |
| 5 | NB800M.05.05.00 | Cylinder cover plug |
| 6 | NB800M.05.06 | Linear pusher |
| 7 | GB/T3452.1-2005 | O ring: 97.5×3.55-G-S |
| 8 | NB800M.05.07 | discharge outlet cover plate : 5 1/8″ |
| 9 | NB800M.05.08 | Discharge pipe |
| 10 | NB800M.05.01.03 | nut: 1 1/2-8UN-2B (SPL) |
| 11 | NB800M.05.09 | Double end bolt : 1 1/2-8UN-2Ax262 |
| 12 | NB800M.05.10 | Valve cover seal ring |
| 13 | NB800M.05.11 | Valve cover |
| 14 | NB800M.05.12 | valve rod guide apparatus |
| 15 | NB800M.05.13.00 | Spring guide |
| 16 | NB800M.05.14 | Guard plate |
| 17 | NB800M.05.15 | bolt: 3/8-16UNC-2Ax20 |
| 18 | GB/T4240-1993 | Steel wire: Φ1.60 (L=1830) |
| 19 | NB800M.05.16 | Valve spring |
| 20 | NB800M.05.17.00 | Valve assembly |
| 21 | NB800M.05.18.00 | Nut, piston |
| 22 | NB800M.05.19.00 | piston: 5 1/2 |
| 23 | NB800M.05.20 | Seal ring, piston |
| 24 | NB800M.05.21 | Piston rod |
| 25 | NB800M.05.22 | double metal cylinder sleeve |
| 26 | NB800M.05.22A | Cylinder sleeve |
| 27 | NB800M.05.23.00 | Spray pipe assembly |
| 28 | NB800M.05.24.00 | catch hoop assembly |
| 29 | NB800M.05.25 | End cover, cylinder sleeve |
| 30 | NB800M.05.26 | washer: 39 |
| 31 | NB800M.05.27 | fixing clip |
| 32 | NB800M.05.28.00 | valve rod guide (lower) |
| 33 | GB/T3452.1-2005 | O RING: 190×7-G-S |
| 34 | ANSI/ASME B18.2.1-1996 | bolt: 7/8-9×1 3/4 |
| 35 | NB800M.05.29.00 | Suction pipeline |
| 36 | NB800M.05.30.00 | shim set |
| 37 | ANSI/ASME B18.2.1-1996 | bolt: 7/8-9×3 1/2 |
| 38 | ANSI/ASME B18.2.2-1987 (R1999) | Nut: 7/8-9 |
| 39 | GB/T3452.1-2005 | O RING: 290×7-G-S |
| 40 | NB800M.05.31 | Suction flange ( I ) |
| 41 | NB800M.05.32 | Screw plug: NPT1 1/2 |
| 42 | NB800M.05.33 | Blanking plate, suction: 10″ |
| 43 | NB800M.05.34 | Suction flange ( II ) |
| 44 | NB800M.05.35.00 | Suction pulsation dampener |
| 45 | 243 | anaerobic adhesive for thread locking and sealing |
| 6、NB800M.06.00 Power end lubrication assembly |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.06.01.00 | Support |
| 2 | NB800M.06.02.00 | shim set |
| 3 |
| 2Sgear oil pump (square key included) |
| 4 | Y60-Z | Dual scale pressure gauge : (9/16-16UN-2B) (0~1.6MPa/0~230psi) |
| 5 | NB800M.06.03 | Inner screw connector : NPT1/4-9/16-16UN-2B |
| 6 | NB800M.06.04 | Seal gasket |
| 7 | NB800M.06.05 | 90°pipe connector: 1/2-20UNF-2A-NPT1/4 |
| 8 | GB/T1527-1997 | Copper pipe: Φ8*965 |
| 9 | GB/T1527-1997 | Copper pipe: Φ8* 1448 |
| 10 | NB800M.06.06.00 | H Pipe clip |
| 11 | GB/T 1527-1997 | Copper pipe: Φ8* 1700 |
| 12 | GB/T 1527-1997 | Copper pipe: Φ8*2057 |
| 13 | NB800M.06.07 | Nut: 1/2 -20UNF-2B |
| 14 | GB/T 1527-1997 | Copper pipe: Φ12*1700 |
| 15 | NB800M.06.08 | 90°pipe connector : 11/16-16UN-2A-NPT1/4 |
| 16 | NB800M.06.09 | Nut: 11/16-16UN-2B |
| 17 | NB800M.06.10 | straight connector: 1/2-20UNF-2A |
| 18 | GB/T 1527-1997 | Copper pipe: 98*698 |
| 19 | NB800M.06.11.00 | Pipe clip: 912 |
| 20 | NB800M.06.12.00 | Pipe clip: 98 |
| 21 | NB800M.06.13 | Straight connector: 11/16-16UN-2A |
| 22 | GB/T 1527-1997 | Copper pipe: Φ12*927 |
| 23 | GB/T 1527-1997 | Copper pipe: Φ12*650 |
| 24 | NB800M.06.14 | Oil nozzle |
| 25 | ANSI/ASME | bolt: 1/4-20*3/4 |
| B18.2.1-1996 |
|
| 26 | GB/T93-1987 | washer: 6 (d1min=6.4) |
| 27 | NB800M.06.15 | 90°pipe connector : 11/16-16UN-2A-NPT3/8 |
| 28 | GB/T 1527-1997 | Copper pipe: Φ12*780 |
| 29 | NB800M.06.16 | Straight connector: 5/8-16UN-2A-NPT1/4 |
| 30 | NB800M.06.17 | Nut: 5/8-16UN-2B |
| 31 | GB/T 1527-1997 | Copper pipe: Φ10*318 |
| 32 | GB/T1527-1997 | Copper pipe: Φ10*152 |
| 33 | NB800M.06.18.00 | Pipe clip: Φ10 |
| 34 | NB800M.06.19 | 90°pipe connector: 5/8-16UN-2A-NPT1/4 |
| 35 | GB/T 1527-1997 | Copper pipe: Φ10*700 |
| 36 | GB/T 1527-1997 | Copper pipe: Φ10*890 |
| 37 | GB/T 1527-1997 | Copper pipe: Φ10*755 |
| 38 | NB800M.06.20 | plug socket ( I ) |
| 39 | NB800M.06.21 | screw plug: NPT3/8 |
| 40 | GB/T 1527-1997 | Copper pipe:Φ10* 184 |
| 41 | GB/T 1527-1997 | Copper pipe: Φ10*508 |
| 42 | GB/T 1527-1997 | Copper pipe: Φ10*610 |
| 43 | GB/T 1527-1997 | Copper pipe: Φ10*365 |
| 44 | GB/T 1527-1997 | Copper pipe: Φ10*630 |
| 45 | NB800M.06.22 | screw plug: NPT1/4 |
| 46 | NB800M.06.23.00 | Filter assembly |
| 47 | NB800M.06.24 | Straight connector : 15/16-16UN-2A-NPT1/2 |
| 48 | NB800M.06.25 | Nut: 15/16-16UN-2B |
| 49 | GB/T 1527-1997 | Copper pipe:Φ16*330 |
| 50 | GB/T 1527-1997 | Copper pipe: Φ16*640 |
| 51 | NB800M.06.26 | plug socket (II ) |
| 52 | NB800M.06.27 | Lower plate |
| 53 | NB800M.06.28 | Straight connector: 1/2-20UNF-2A-NPT1/4 |
| 54 | GB/T 1527-1997 | Copper pipe: Φ8*340 |
| 55 | YYFJ-L20 | Relief valve |
| 56 | NB800M.06.29 | 90°pipe connector : 15/16-16UN-2A-NPT1/2 |
| 57 | ASMEB 18.3-2002 | Bolt: 5/16-18*1 9/16 |
| 58 | GB/T93-1987 | washer: 8 |
| 59 | NB800M.06.30.00 | Double pipe clip: Φ8 |
| 60 | NB800M.06.31.00 | gear assembly, oil pump |
| 61 | TS1609 ^ TS1680 | anaerobic adhesive for cylindrical part |
| 7、NB800M.08.00 Liner spraying assembly |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.08.01.00 | Shield |
| 2 | NB800M.08.01.00A | Shield |
| 3 | NB800M.08.02 | Belt pulley |
| 4 | GB/T1171-1996 | V belt: A2800 |
| 5 | NB800M.08.03.00 | Support assembly |
| 6 | NB800M.08.03.00A | Support assembly |
| 7 | NB800M.08.04 | Connector: NPT1-1 5/8-12UNF-2A |
| 8 | NB800M.08.05 | Short connector: NPT1 |
| 9 | NB800M.08.06 | Connector: NPT1-1 5/16-12UNF-2A |
| 10 |
| Hose assembly : C31.5 I-950 (The connection screw on both ends are1 5/8-12UNF-2B) |
| 11 |
| Hose assembly: C25 I -1500 (The connection screw on both ends are 1 5/16-12UNF-2B) |
| 12 | NB800M.08.07 | Connector: NPT2 1/2-1 5/8-12UNF-2A |
| 13 | NB800M.08.08.00 | Support |
| 14 | NB800M.08.08.00A | Support |
| 15 | NB800M.08.09.00 | Water tank |
| 16 | NB800M.08.10.00 | Tank cover |
| 17 | 32SB180J (32PL) | centrifugal spray pump (West petroleum or Baoji) |
| 18 | Q11F-16 | Inner screw ball valve: NPT1 |
| 19 | NB800M.08.11 | Flange: NPT1 |
| 20 | NB800M.08.12 | Washer |
| 21 | ANSI/ASME | Bolt: 5/16-18×1 |
| B18.6.2-1998 |
|
| 22 | ANSI/ASME | bolt: 5/8-11×2 |
| B18.2.1-1996 |
|
| 23 | GB/T93-1987 | washer: 16 |
| 24 | ANSI/ASME B18.2.2-1987 (1999) | Nut: 5/8-11 |
| 25 | ANSI/ASME | bolt: 5/8-11×1 1/4 |
| B18.2.1-1996 |
|
| 26 | GB/T95-2002 | washer: 16 |
| 27 | NB800M.08.13 | Connection plate |
| 28 | ANSI/ASME | bolt: 1/2-13×1 1/2 |
| B18.2.1-1996 |
|
|
|
|
| 29 | GB/T93-1987 | washer: 14 |
| 30 | NB800M.08.14 | 90°elbow: NPT1 |
| 31 | ANSI/ASME | bolt: 1/2-13×2 3/8 |
| B18.2.1-1996 |
|
| 32 | ANSI/ASME | Nut: 1/2-13 |
| B18.2.2-1987 |
|
| (R1999) |
|
| 8、NB800M.10.00 Breather cap |
|
| S.N | Drawing no. | Item |
| 1 | NB800M. 10.01 | Baffle plate |
| 2 | NB800M.10.02 | Connection plate ( I ) |
| 3 | NB800M. 10.03 | Gasket |
| 4 | NB800M.10.04 | Connection plate (II ) |
| 5 | ANSI/ASME B18.2.1-1996 | bolt: 3/8-16×1 |
| 6 | NB800M. 10.05 | Connector |
| 7 | NB800M.10.06 | Press plate for filter screen |
| 8 | NB800M. 10.07 | Copper mesh |
|
|
|
| 9 | NB800M. 10.08 | Upper cover |
| 10 | ANSI/ASME B 18.6.3-2003 | Bolt: 10 (0.190) 0-24×3/8 |
| 9、NB800M.15.00 Oil level gauge assembly |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.15.01.00 | dipstick |
| 2 | NB800M.15.02 | Short connector: NPT1/2 |
| 3 | NB800M. 15.03 | Elbow: NPT1/2 |
| 10、NB800M.19.00 Clean out cover |
|
| S.N | Drawing no. | Item |
| 1 |
| Cover plate assembly: Φ152.4*12.7 |
| 2 | NB800M.19.01 | Connector: NPT3/4 |
| 3 | NB800M. 19.02 | screw plug: NPT3/4 |
| 11、NB800M.22.00 Draining filter assembly |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.22.01.00 | Filter screen assembly |
| 2 | NB800M.22.02 | Shell |
| 3 | GB/T3452.1-2005 | O RING: 165×7-G-S |
| 4 | NB800M.22.03 | Double ends bolt: 1 1/2-8UN (12UNF) -2Ax128 |
| 5 | NB800M.22.04 | Nut: 1 1/2-8UN-2B (SPL) |
| 12、NB800M.24.00 Elbow assembly |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.24.01.00 | Seat, pressure gauge |
| 2 | NB800M.24.02.00 | Safety valve seat |
| 3 | NB800M.24.03.00 | Discharging cross |
| 4 | NB800M.24.04 | Double ends bolt: 1 1/16-8UN-2Ax180 |
| 5 | NB800M.24.05 | Thickened nut: 1 1/16-8UN-2B (SPL) |
| 6 | NB800M.24.06 | Gasket ring: R27 |
| 7 | 243 | anaerobic adhesive for thread locking and sealing |
| 13、NB800M.24.00A Discharge five-way pipe assembly |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.24.01.00A | Seat, safety valve |
| 2 | NB800M.24.02A | Discharge five-way pipe |
| 3 | NB800M.24.03.00A | Seat, pressure gauge |
| 4 | NB800M.24.04A | Gasket ring: R35 |
| 5 | NB800M.24.05A | Double ends bolt: 1 1/8-8UN (12UNF) -2Ax90 |
| 6 | NB800M.24.06A | Nut: 1 1/8-8UN-2B (SPL) |
| 7 | NB800M.24.07A | Double ends bolt: 1 1/2-8UN (12UNF) -2Ax130 |
| 8 | NB800M.24.08A | Nut: 1 1/2-8UN-2B (SPL) |
| 9 | NB800M.24.09A | Gasket ring: R44 |
| 10 | NB800M.24.10.00A | Support bracket |
| 11 | ANSI/ASME | bolt: 7/8-9×2 3/8 |
| B18.2.1-1996 |
|
| 12 | GB/T93-1987 | washer: 22 |
| 13 | NB800M.24.11A | Gasket |
| 14 | ANSI/ASME | bolt: 7/8-9×3 1/8 |
| B18.2.1-1996 |
|
| 15 | ANSI/ASMEB 18.2.2 -1987 (R1999) | Nut: 7/8-9 |
| 16 | NB800M.24.12A | Connection plate |
| 17 | NB800M.24.13.00A | Support |
| 14、NB800M.27.00 KB-45 Pulsation Dampener |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.27.01 | Gasket ring: R39 |
| 2 | NB800M.27.02 | Base plug |
| 3 | NB800M.27.03.00 | Air rubber |
| 4 | NB800M.27.04.00 | Shell assembly |
| 5 | NB800M.27.05 | Cover |
| 6 | JZR3-L8 | Check valve (Xinhua hydraulic device, Fenghua) |
| 7 | NB800M.27.06.00 | Cover, pressure gauge |
| 8 | NB800M.27.07 | Connector: NPT1/4 |
| 9 | Y-60 | Double scale shock proof pressure gauge: 0—25MPa (0—3630psi) |
| 10 | NB800M.27.08 | washer |
| 11 | NB800M.27.09 | T-joint: NPT1/4 |
| 12 | NB800M.27.10.00 | Air discharge valve |
| 13 | NB800M.27.11.00 | Suction hose assembly, pulsation dampener |
| 15、NB800M.28.00 JA-3 shear pin safety valve |
|
| S.N | Drawing no. | Item |
| 1 | NB800M.28.01 | Connector |
| 2 | NB800M.28.02 | Retainer ring |
| 3 | NB800M.28.03.00 | Piston assembly |
| 4 | NB800M.28.04 | Valve body |
| 5 | NB800M.28.05 | Piston rod |
| 6 | NB800M.28.06 | Buffer mat |
| 7 | NB800M.28.07 | Elastic cylinder pin |
| 8 | NB800M.28.08 | Lock spring |
| 9 | NB800M.28.09 | Shield |
| 10 | NB800M.28.10 | Shear pin plate |
| 11 | NB800M.28.11 | Shear pin |
| 12 | NB800M.28.12 | Instruction plate |
| 13 | NB800M.28.13 | Pin shaft |
| 14 | NB800M.28.14 | Steel wire retainer ring |
| 15 | NB800M.28.15 | Name plate |
| 16 | GB/T91-2000 | Pin: 4×25 |
| 17 | ANSI/ASME B 18.6.3-2003 | Bolt: 8 (0.164) -32×5/8 |
| 18 | ANSI/ASME B 18.6.3-2003 | Nut: 8 (0.164) -32 |
| 19 | ANSI/ASME B18.2.1-1996 | bolt: 3/8-16×4 3/8 |
| 20 | ANSI/ASMEB 18.2.2-1987(R1999) | Nut: 3/8-16 |
| 21 | ANSI/ASME B 18.6.3-2003 | Bolt: 5 (0.125) -40×5/16 |
Telephone
E-MAIL